Skip to Content

How to Make Resin and Wood Wall Art that GLOWS

How to Make Resin and Wood Wall Art that GLOWS

In this tutorial, I show you how to make resin and wood wall art (or table) that glows in the dark.  Additionally, this surfboard wall art also functions as a table.

Tools and Materials I Used

Below are the tools I used for this resin and wood wall art project.

Material

Tools

 

Often times, I experiment with many different products and tools while working with epoxy resin.  Therefore, the products I use in a certain project may not be my favorite.

For your convenience, I’ve compiled a complete list of my favorite Epoxy Resin material and tools – click HERE to see the list.

Making Resin and Wood Wall Art_Pinterest

 

Resin and Wood Wall Art DIY Digital Plans

I’m in the process of finishing a very detailed, downloadable tutorial for this wood and resin project.

Complete the form below and I’ll notify you as soon as they are ready. 

Also, I’ll add a bonus to those who sign up for this notification. 

[convertkit form=5255654]

 

Making Resin and Wood Wall Art

Be sure to visit my resin wood art for sale or my other wood and resin projects.

First, I obtained this piece of Cypress wood from a local cypress sawmill in Louisiana.

This piece of cypress was in the scrap wood pile, so I grabbed it on my way out after I received permission from the owner.

Ultimately, this piece of cypress wood was located at the top of the trunk just before the tree split into 2 main branches.

In turn, the wood sort of looked similar to a pair of pants. 

Regardless, I liked it and knew I could make something unique with it.

how to make wood and resin wall art that glows_reclaimed cypress wood

 

This piece of cypress sat around my shop for months until I finally decided to run it through my planer to get a better view of the grain. 

The grain of this cypress wood is simply beautiful, so I decided to start my project the following week.

 

Surfboard Wall Art

As you know if you follow my projects, my family and I love anything that has to do with the ocean. 

In turn, I decided to make a resin and wood surfboard that can be wall art or a small table.

Essentially, that is the background on this epoxy wall art.

So, it is time to walk you through the steps on how to make resin and wood wall art that glows.

 

Prepare Resin Mold

I prepared the resin mold for this epoxy resin wood art by using the same piece of 1/8″ melamine I used on my Sand Dollar River Glow Table.

First, I used my air compressor to remove loose debris.

how to make wood and resin wall art that glows_remove loose debris

 

Next, I applied furniture wax to the bottom of the table before laying the cypress wood on top.

how to make wood and resin wall art that glows_furniture wax

 

Then, I used my brad nailer with 1.5″ brad nails to secure scrap 1x2s to the back and 2 sides of the wood.  Also, I covered the scrap pieces of wood with packing tape covered with furniture wax to prevent sticking.

how to make wood and resin wall art that glows_brad nail wood to mold

 

Next, I clamped a scrap piece of 2×4 on top of the table to hold it down.

how to make wood and resin wall art that glows - secure to table

 

Then, I used a scrap 2×4 on the opposite.  This 2×4 was severely warped, which was fine since it resembled the shape of a surfboard side.

While the boards were secured with clamps, I sealed the wood on the inside and outside of the table with silicone caulk.

 

First Resin Pour

I wanted the void in the middle of the table to be transparent blue and the side of the table to be opaque blue.

Essentially, the transparent blue resin part of the resin and wood wall art would be shallow water and the opaque blue would represent deeper water.

First, I mixed 1 large batch of epoxy resin and split them equally in 2 different containers.

Next, I put one drop of transparent blue dye in one container and sky blue pearl pigment powder in the other container.  Also, I used transparent resin on this resin wall art project as well.

 

Then, I added sky blue pearl pigment powder and neutral sky blue glow powder to the second container.

 

I mixed the pigment and glow powder for roughly 3 minutes.

how to make wood and resin wall art that glows - mix pigment powder and glow powder in epoxy resin

 

Quick Tip for Resin Measuring and Mixing

As a quick tip, always use the inside of the measuring cup when pouring resin as opposed to outside. 

By using the inside, you will be much more accurate.

Also, I use a sequence when mixing resin to make certain it is mixed correctly. 

Furthermore, I explain my method in the video at the top of this page.

 

Blending Resin

First, I poured the transparent blue resin within the void.  Once the transparent blue resin reached the end of wood and resin surfboard, I poured the opaque blue.

Next, I covered the section on side of the wood and resin art with the opaque blue resin.  The depth of the resin pour ended up being about 3/8″.

 

Then, I used my heat gun to remove bubbles and further blend the resin.

Second Resin Pour

First, I mixed a large batch of resin the following day and split the resin into 3 different containers.

The first container contained transparent blue dye, the second contained sky blue pearl pigment, and the third contained sapphire blue pigment.  

Additionally, I added fluorescent blue glow powder to the second and third containers.

 

Complete the form below and I’ll notify you when the DIY digital plans for this wood and resin wall art project are ready.  You’ll be the first to be notified and I’ll email you a 25% off discount code.

[convertkit form=5255654]

Next, I poured these in a methodical way to facilitate proper blending and color patterns.

 

Third Resin Pour

First, I mixed pearl white pigment with a small batch of resin immediately after the second resin pour.

how to make wood and resin wall art that glows_resin pearl white pigment

 

Next, I drizzled this resin in front of the sapphire blue resin on side of the wood and resin surfboard.  

Essentially, the purpose of this white is to represent wave crests and crashing waves.

how to make wood and resin wall art that glows_resin pearl white pigment drizzle

 

Then, I blended the resin together with my heat gun until the pearl white pigment looked cool to me.

 

Fourth Resin Pour

First, I mixed a medium sized batch of resin with transparent blue dye immediately following the third resin pour.

Essentially, I needed more transparent blue dye to pour in the void to push the opaque resin back out to sea.  The darker blue was creeping into the transparent dye too much.

Additionally, I needed about 1/8″ more to complete the resin pour and move to the next step.

 

Next, I used my heat gun to blend the resin and remove bubbles.

Then, I let the resin cure for 24 hours.

 

Making Resin and Wood Wall Art that Glows – Black Light Test

While the resin was curing, I tested the glow powder with a black light.  

The black light quickly charges the glow powder and it is a great way to test the glow powder.

First, I turned off the lights and held the black light on the glow powder for a few seconds.  

The longer the black light shines on the glow powder, the brighter the resin glows.

Ultimately, I find shining the black light for 3 to 5 seconds provides an accurate representation of how bright the resin will glow.

 

Remove Mold

Two days after the fourth resin pour, I removed the resin mold with relative ease.

First, I used a rubber mallet to tap on the sides until the wood and resin wall art releases.

 

Next, I lifted the wood and resin surfboard from the melamine easily.

how to make wood and resin wall art that glows_remove resin and wood wall art from melamine

 

Rough Sanding of Resin and Wood Wall Art

After I removed the resin and wood wall art from the mold, I used my festool RO125 sander with 40 grit sandpaper to rough sand the entire piece.

Ultimately, the purpose of this step is to get the resin and wood surfboard as flat as possible by removing the high spots and rough areas.

how to make wood and resin wall art that glows_resin rough sanding 40 grit sandpaper

 

I realize the festool sanders are more expensive than most sanders.  However, this is when they are worth every penny.  

Additionally, the dust collection on this sanders catch the majority of resin and wood dust particles.

In order to accomplish this epoxy resin wood art without it, I would need an orbital sander, belt sander, and twice the amount of time.

 

Surfboard Template

First, I used Kraft paper and covered one side of the board.

Next, I flipped the board over and cut out the Kraft paper the exact size of the board.  Or, as close as possible to exact.

 

Then, I flipped the resin and wood surfboard over again.  

I folded the Kraft paper in half, sketched a half moon, and cut it out with a pair of scissors making sure to stay just outside the lines.

how to make wood and resin wall art that glows_cut out surfboard template with scissors

 

There is a trick I show you in my digital plans to get a perfect point at the front of the board and a square in the back.  

I also share the measurements and a digital copy of the template I used.  

So, complete the form below and I’ll notify you as soon as they are ready.  

Also, I’ll add a bonus to those who sign up for this notification.  ????

[convertkit form=5255654]

 

Next, I used painters tape to tape the wood and resin surfboard template to the board.

 

Then, I traced it with a pencil and used my jigsaw to cut it out just outside the line.

how to make wood and resin wall art that glows_surfboard template cut out with jig saw

 

Finally, I used my rotary sander with 40 grit sandpaper to sand up to the pencil line.

how to make wood and resin wall art that glows_surfboard template sand up to line

 

Roundover Edges

After the rough sanding was complete, I used my trim router with a 1/2″ roundover bit to roundover the top and bottom.

 

Shape Surfboard

To shape the resin and wood wall art to look like a real surfboard, I used my sander with 40 grit sandpaper along with my block plane.

First, I flipped the surfboard around (top facing down) and I removed the material with my 40 grit sandpaper.  I started at the tip and worked by way back to create the upward angle.

Next, I used my block plane to smooth out any indentions from the sander.  40 grit sandpaper is a very course grit and removes material very quickly.  Consequently, it causes indentations on the board.

 

Solder LED Lights and Battery

Even though this surfboard will glow without LED lights, I decided to add them to the bottom in case the resin and wood wall art is placed in an area with low light.

Furthermore, the resin and wood surfboard is meant to be wall art.  Therefore, I used a rechargeable battery with an on/off switch to prevent the need for a power cord or wall outlet behind it.

First, I soldered 2 small LED light strips together.  Soldering is a great skill to learn as it can be used in many different applications.  Checkout this post for more detail on how to solder LED light strips.

Next, I used my heat gun to heat the shrink wrap in order to protect the solder.

 

Then, I soldered a male plug to one end of one LED light strip.  This male connector will connect to the battery to power the lights.

how to make wood and resin wall art that glows_solder male plug

 

Finally, I connected the LED light strips to the rechargeable battery to make sure they work.  And, they did.  :)

 

Hidden Battery Compartment

The battery is about 1″ thick, which would create a space between the wall and the resin and wood wall art.

So, I decided to use my router with a straight bit and create a small compartment in the back of the surfboard.  Also, I made the compartment to fit the battery charger both horizontally and vertically.

First, I drew the outline.  Next, I used my dremel tool to create a pathway to start my router.

I removed 1/8 of material at a time until the I reached 3/4″, which allowed the battery to slightly protrude to access the switch.  This allows access to the on/off switch without needing to take the wall art from the wall.

 

Then, I used my chisel to clean up the edges.

Sanding Resin and Wood Wall Art

Now, to the fun part of the resin and wood wall art project.  I’m kidding, it is my least favorite part of any project.  However, it is very important.

First, I used 80 grit sandpaper to sand the top and bottom with my festool sander.

 

Next, I worked my way through the grit sequence

 

Then, I wiped the surface with a damp rag to raise the grain and sanded with 320 grit sandpaper.

 

Oil and Urethane Satin Finish

After sanding, I proceeded to applying a finish to the resin and wood wall art.

I used an oil based urethane Satin finish by General finishes on the top and bottom of the resin and wood wall art.

how to make wood and resin wall art that glows_oil and urethane satin finish

 

First, I applied the first coat with a lint free rag.

Quick Tip:  Smooth out the finish by making a soft circle with the rag and lightly wiping the length of the table.

 

Next, I hand sanded with 320 grit sandpaper and applied a second coat.

how to make wood and resin wall art that glows_sand between coats

 

Then, I repeated the process above for the third and final coat.

how to make wood and resin wall art that glows_final finish coat

I receive a ton of questions regarding the finishes I use on my epoxy resin projects.  Ultimately, I have 3 favorite finishes (not including this one) I use on my resin projects, which I talk about extensively in my digital plans.

So, complete the form below and I’ll notify you as soon as they are ready.  Also, I’ll add a bonus to those who sign up for this notification.

[convertkit form=5255654]

 

Hairpin Legs

As I previously stated, this resin and wood wall art can also be an end table or couch table.  So, I used a set of hairpin legs I had in my shop from a previous project.

To install the hairpin legs, I centered the back and front pair both vertically and horizontally.

how to make wood and resin wall art that glows_center hairpin legs

 

Next, I marked the holes and drilled pilot holes.

how to make wood and resin wall art that glows_drill pilot holes for hairpin legs

Then, I secured the table with screws.

 

Install LED Light Strip

After I secured the hairpin legs, I installed the LED light strip.

First, I placed the rechargeable battery in the compartment and secured it with hot glue.

Next, I laid out the LED light strips and peeled off the paper covering the adhesive side.  Then, I pressed them down and secured the LED light strip with hot glue for extra security.

Conclusion

In conclusion, I hope you learned how to make resin and wood wall art that glows and it brought you some form of value.

Let me know in the comments if you prefer the resin and wood wall art or table.  I have other resin wall art projects such as a baseball bat rack and Mardi Gras resin art.

Checkout my epoxy resin ocean craft table that GLOWS or my epoxy resin river glow table with embedded sand dollars.

Gary Huxley

Monday 2nd of November 2020

Hi Im a woodwork teacher and looking at introducing new jobs and live near the beach, most of the students surf. So this is what I have been looking for, great video.

Jeremy

Wednesday 18th of November 2020

Hi Gary, thanks so much for the compliment! These beach inspired tutorials may be of interest to you:

Seashell Table Ocean Table Wood and Resin Wall Art Ocean Art DIY Plans Ocean Table DIY Plans

Fonda

Thursday 20th of September 2018

It's great as wall art. I like the table but not so sure about the legs

Bob Johnson

Thursday 20th of September 2018

As a wall art it's a bit large but would work excellent for an accent feature if you paint the wall an ocean scene. This would make a good accent wall for a room. The glow in the dark feature would make for a night light.???? But it would work for a coffee table in a small room in a beach house. I guess it's up to the owner as to what to do with it. Nice job either way.

Adrian Bruce

Thursday 20th of September 2018

I really like the surf board table but I think as wall art will look just as great. Also, thank you for each item you used was shown in plain view. Showing your step by step process will help me with a few missing pieces to do the same process. Amazing good! Look fantastic!!!

Comments are closed.